1 2
Blaze Performance  |  SKU: BLZ-02E01C01A

Blaze Performance AToM V2 Intake System - VW/Audi MQBe Golf R (Mk8) / S3 (8Y) 2.0T

$ 432.00

Shipping rates and applicable discounts are applied during checkout.

Description
Blaze + EQT North America

Upgrades from certain intakes may necessitate revision to boost strategy. Please submit a datalog to your calibrator for review to ensure tune optimization. 

*Fitment Note: Due to the large ducting to scoop maximum amounts of air, certain aftermarket hoods that have center vents may have clearance issues. We recommend checking out Vaarticus' install video as a reference for clearance.

This intake system features a full-width air deflector to ram as much air as possible into the engine through the massive 120mm air filter!

Significant gains have been shown on our Stock Turbo powered Mk8 Golf R when compared to the factory inlet/intake which can be seen on the dyno chart below where all testing was performed back to back on our Mustang chassis dyno, with identical ambient conditions. We also took great care to make sure fluid and even tire temperatures were consistent. Finally, we chose the average runs out of each set of 4 for the comparison. No cherry picking here, we really wanted to see what kind of gains these parts offer in a fair environment.

Cleaning Instructions

For filter cleaning instructions, check out our FAQ 

Blaze Comparison - Stage 1 Custom - Crank
As you may know, the MK8 Golf R has a turbine speed sensor built in from the factory. This is an extremely valuable tool in determining effectiveness of aftermarket parts and tuning and gathering general data. So the final chart you will see below is an overlay of log data including boost (in psiA), and turbine speed.

Both sets of data are from our OTS Stage 1 E85 tune; red is with the stock intake, and blue is with the Blaze intake. You can see that while boost levels remain very similar, the turbine speed with the stock intake is significantly higher throughout the pull. At the top end, you can see that it peaks and starts to drop off as it hits the speed limit we set in our tune. With the Blaze intake installed, the turbine speed is well under that limit and actually allows the ECU to hold a bit more boost at the very top.
Features
  • 100mm (4") Case Outlet
  • 4-Ply Steel Reinforced Turbo Inlet Pipe
    (100mm Inlet ID, 76mm Outlet ID)
  • 56mm ID Turbo Inlet Flange with Viton O-Ring
  • 160mm Air Accumulator / Heat Shield
  • Rubber Seal for a tight fit to the hood
  • Reverse Mounted 120mm Washable Cone Filter
  • Full-Width Cowl for optimum airflow
Vehicle Fitment
  • VW Golf R (Mk8 / Audi S3 (8Y)
Installation

For Installation instructions click HERE (Coming Soon)

Dyno Charts

Golf R (Stage 1): E85

  • Crank Horsepower

Blaze Comparison - Stage 1 MK8 91 - Crank

  • Wheel Horsepower

Blaze Comparison - Stage 1 91 - Wheel

Golf R (Custom Tune): E60

  • Crank Horsepower

Blaze Comparison - Stage 1 Custom - Crank

  • Wheel Horsepower

Blaze Comparison - Stage 1 Custom - Wheel


× ⇓

Terms and Conditions Acknowledgement

By continuing with your purchase, you agree to our Terms and Conditions, which include our Refund Policy, Privacy Policy, Shipping Policy, and Terms of Service.

By clicking "Agree," you acknowledge that you have read, understood, and agree to all the terms and conditions outlined in these policies.

Blaze Performance AToM V2 Intake System - VW/Audi MQBe Golf R / S3 2.0T (Mk8 / 8Y) - Equilibrium Tuning, Inc.
Blaze Performance

Blaze Performance AToM V2 Intake System - VW/Audi MQBe Golf R (Mk8) / S3 (8Y) 2.0T

From $ 432.00 $ 480.00
Blaze + EQT North America

Upgrades from certain intakes may necessitate revision to boost strategy. Please submit a datalog to your calibrator for review to ensure tune optimization. 

*Fitment Note: Due to the large ducting to scoop maximum amounts of air, certain aftermarket hoods that have center vents may have clearance issues. We recommend checking out Vaarticus' install video as a reference for clearance.

This intake system features a full-width air deflector to ram as much air as possible into the engine through the massive 120mm air filter!

Significant gains have been shown on our Stock Turbo powered Mk8 Golf R when compared to the factory inlet/intake which can be seen on the dyno chart below where all testing was performed back to back on our Mustang chassis dyno, with identical ambient conditions. We also took great care to make sure fluid and even tire temperatures were consistent. Finally, we chose the average runs out of each set of 4 for the comparison. No cherry picking here, we really wanted to see what kind of gains these parts offer in a fair environment.

Cleaning Instructions

For filter cleaning instructions, check out our FAQ 

Blaze Comparison - Stage 1 Custom - Crank
As you may know, the MK8 Golf R has a turbine speed sensor built in from the factory. This is an extremely valuable tool in determining effectiveness of aftermarket parts and tuning and gathering general data. So the final chart you will see below is an overlay of log data including boost (in psiA), and turbine speed.

Both sets of data are from our OTS Stage 1 E85 tune; red is with the stock intake, and blue is with the Blaze intake. You can see that while boost levels remain very similar, the turbine speed with the stock intake is significantly higher throughout the pull. At the top end, you can see that it peaks and starts to drop off as it hits the speed limit we set in our tune. With the Blaze intake installed, the turbine speed is well under that limit and actually allows the ECU to hold a bit more boost at the very top.
Features
Vehicle Fitment
Installation

For Installation instructions click HERE (Coming Soon)

Dyno Charts

Golf R (Stage 1): E85

Blaze Comparison - Stage 1 MK8 91 - Crank

Blaze Comparison - Stage 1 91 - Wheel

Golf R (Custom Tune): E60

Blaze Comparison - Stage 1 Custom - Crank

Blaze Comparison - Stage 1 Custom - Wheel


Select Design

  • Standard
  • Gloss Carbon Fiber
  • Matte Carbon Fiber
  • Forged Carbon Fiber
View product
Back to top